Toggle navigation
Login
Register
Itoo Software Forum
»
RailClone
»
RailClone Pro (*)
»
RC as hypotenuse segment
« previous
next »
Print
Pages: [
1
]
Author
Topic: RC as hypotenuse segment (Read 619 times)
arch3d
Sr. Member
Posts: 281
RC as hypotenuse segment
«
on:
July 19, 2022, 01:46:21 PM »
Hi,
Is it possible to use A1S as hypotenuse segment, or its RC limitation?
It works perfect with regular segments but i would like to avoid messing with Composites
Best
Michal
«
Last Edit: July 19, 2022, 01:50:40 PM by arch3d
»
Logged
arch3d
Sr. Member
Posts: 281
Re: RC as hypotenuse segment
«
Reply #1 on:
July 19, 2022, 01:55:47 PM »
Here is example based on regular segment
Logged
Paul Roberts
iToo Software
Hero Member
Posts: 2993
Re: RC as hypotenuse segment
«
Reply #2 on:
July 19, 2022, 03:01:17 PM »
Hi!
Thanks for the question. It's possible, you just need to tell RailClone which generator in the chain you wish to use for the X Spline Length. You do it like this, using the name of the generator:
I hope that helps,
Paul
Logged
Paul Roberts
iToo Software
arch3d
Sr. Member
Posts: 281
Re: RC as hypotenuse segment
«
Reply #3 on:
July 19, 2022, 03:09:51 PM »
So simple! Easier way is always hard to find
Thank you very much:)
Logged
arch3d
Sr. Member
Posts: 281
Re: RC as hypotenuse segment
«
Reply #4 on:
July 19, 2022, 03:46:21 PM »
Paul
Something harder here:)
I put it into markers and have no idea from where is gap
Cheers
Logged
Paul Roberts
iToo Software
Hero Member
Posts: 2993
Re: RC as hypotenuse segment
«
Reply #5 on:
July 19, 2022, 04:43:04 PM »
Please find attached a revised version. I've just tweaked the trig expressions and few other things a little bit.
Hope it helps.
Paul
Logged
Paul Roberts
iToo Software
arch3d
Sr. Member
Posts: 281
Re: RC as hypotenuse segment
«
Reply #6 on:
July 19, 2022, 05:17:40 PM »
Works perfect
Thank you
Logged
arch3d
Sr. Member
Posts: 281
Re: RC as hypotenuse segment
«
Reply #7 on:
July 19, 2022, 06:27:00 PM »
Paul
I didnt notice it before sorry for that.
What if spline isnt flat?
I have to make a lot of trusses so it seems to be importnant as well.
Only solutution which I can find is make A1S segment verical vithout slope fixing
Cheers
Logged
Paul Roberts
iToo Software
Hero Member
Posts: 2993
Re: RC as hypotenuse segment
«
Reply #8 on:
July 20, 2022, 12:45:21 PM »
Is that solution working well enough? It might be possible to find the angle of the spline, but it could get quite complicated!
Best,
Paul
Logged
Paul Roberts
iToo Software
arch3d
Sr. Member
Posts: 281
Re: RC as hypotenuse segment
«
Reply #9 on:
July 20, 2022, 12:52:01 PM »
I will see on complex object. It might be ok. If you say its complicated i dont even think about it.
Many thanks its much more better than compose mode ( less distortion in vertical mode
Many thanks
M
Logged
Print
Pages: [
1
]
« previous
next »
Itoo Software Forum
»
RailClone
»
RailClone Pro (*)
»
RC as hypotenuse segment
×
Welcome,Guest
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length