Toggle navigation
Login
Register
Itoo Software Forum
»
RailClone
»
RailClone Lite
»
Decorative tile pattern
« previous
next »
Print
Pages: [
1
]
Author
Topic: Decorative tile pattern (Read 38533 times)
anthonyhartleydenton
Newbie
Posts: 9
Decorative tile pattern
«
on:
February 08, 2024, 02:58:54 PM »
Hi All
new to the forum and was wondering if anyone might be able to help. I am using Railclone preset. the pattern and colour are perfect but I need to get the half-moon feature tiles to run in a 3, not a 2 and only in the location on the drawing.
Could anyone point me in the direction of the parameters I should be looking at?
thanks, Tony
Logged
Michal Karmazín
iToo Software
Hero Member
Posts: 2743
Re: Decorative tile pattern
«
Reply #1 on:
February 08, 2024, 03:19:00 PM »
Hi Tony,
The easiest way would probably be to use two
Clipping Areas
(to use these "decorative tiles" just at the specified location) - either within two individual RC objects or within two Generators within one RC object. You can adjust the number of "decorative tiles" by setting the "
Decorative Tile Y Count
" parameter. I hope that helps.
Best regards,
Logged
anthonyhartleydenton
Newbie
Posts: 9
Re: Decorative tile pattern
«
Reply #2 on:
February 08, 2024, 04:40:12 PM »
is there not a way to do it by modifying the settings of the template already in the library? I have it applied to all the buildings already so it would be easier. creating separate clipping areas across multiple facades and 14 buildings will be time-consuming. thanks T
Logged
Michal Karmazín
iToo Software
Hero Member
Posts: 2743
Re: Decorative tile pattern
«
Reply #3 on:
February 09, 2024, 08:37:03 AM »
Well, if "decorative tiles" should always be placed at the same height, you can try raising the "
Standard Tile Y Count
" value (which drives the counter in the
Sequence
Operator) until it fits your needs.
Best regards,
Logged
anthonyhartleydenton
Newbie
Posts: 9
Re: Decorative tile pattern
«
Reply #4 on:
February 19, 2024, 05:53:17 PM »
Hi Michal thanks for the help. so I've got the following and two queries if you might be able to help.
1. how to i get 3 rows of tiles?
2. how do i shunt the 3 rows downward to align where shown. If tried changing the y count up when the numbers gets too small more decorative tiles keep appearing top and bottom.
thanks again T
Logged
Michal Karmazín
iToo Software
Hero Member
Posts: 2743
Re: Decorative tile pattern
«
Reply #5 on:
February 21, 2024, 09:21:22 AM »
You can adapt the style a bit to support two different
Standard Tile Y Count
values by connecting the corresponding
Random
Operator to the
Sequence
Operator (and optionally exporting the
Counter
parameter to the UI) as shown in the attached screenshot. I hope that helps.
Best regards,
Logged
anthonyhartleydenton
Newbie
Posts: 9
Re: Decorative tile pattern
«
Reply #6 on:
February 22, 2024, 04:53:35 PM »
hey thanks for that
also how to i pipe in the second Y count?
how do i export to the UI?
Logged
anthonyhartleydenton
Newbie
Posts: 9
Re: Decorative tile pattern
«
Reply #7 on:
March 05, 2024, 01:55:29 PM »
Hi All another question relating to hanging tiles.
My decorative hanging tiles stop a full tile short of the end. How would I make them run to the corner, please?
thanks in advance T
Logged
Print
Pages: [
1
]
« previous
next »
Itoo Software Forum
»
RailClone
»
RailClone Lite
»
Decorative tile pattern
×
Welcome,Guest
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length